[QRD SPARK N5] Cómo resolver la desviación del joystick en QRD Spark N5 – qrdgame

Cómo solucionar el problema de la deriva del joystick QRD Spark N5

Cómo resolver la deriva del joystick QRD Spark N5

Algunos jugadores pueden experimentar la deriva del joystick al usar el controlador QRD Spark N5. Este problema a menudo se relaciona con la desalineación de la tapa del joystick o la calibración automática de los joysticks de efecto Hall. A continuación, se presentan dos sencillos pasos para ayudarle a resolver este problema y restaurar el uso normal:

Paso 1: Ajuste manualmente la posición del joystick

Debido a largos períodos de envío, la tapa del joystick puede soltarse del sensor Hall dentro del controlador, causando que el joystick derive. Recomendamos ajustar manualmente la tapa del joystick para asegurar que esté correctamente alineada en el centro.

Cómo realizarlo:

  1. Desconecte el controlador: Primero, desconecte el controlador de la consola o de cualquier dispositivo.

  2. Retire la tapa del joystick: Tire suavemente de la tapa del joystick para quitarla del joystick.

  3. Ajuste la tapa del joystick: Después de quitar la tapa, gire lentamente la base de la tapa del joystick en el sentido de las agujas del reloj o en sentido contrario de 3 a 4 vueltas. Asegúrese de que no haya holgura o resistencia inusual durante este proceso.

  4. Realinee al centro: Una vez que la rotación sea suave, asegúrese de que la tapa del joystick esté alineada al centro y luego presiónela suavemente para asegurarla en su lugar.

 

🕹️Paso 2: Cambie de calibración automática a calibración manual

¿Por qué la calibración manual?

El QRD Spark N5 está equipado con joysticks de efecto Hall que originalmente dependían de la calibración automática. Sin embargo, algunos usuarios informaron de deriva del joystick cuando las palancas no estaban completamente inactivas durante el inicio.

Para abordar esto, introdujimos un modo de calibración manual en el firmware V3.05, lo que permite a los jugadores desactivar la calibración automática y calibrar manualmente sus joysticks. Esto garantiza un control más preciso y elimina los problemas de deriva.

👉 Importante: Debe actualizar su controlador al firmware V3.05 antes de que la calibración manual esté disponible.
Descargar aquí:
https://qrdgame.com/blogs/software/v3-1-06-qrd-spark-n5-firmware-version-3-1-06-release


Calibración manual:

  • - con el controlador apagado, mantenga presionados [TURBO+OPTION+HOME] durante 3 segundos para ingresar al menú de configuración de calibración. ([LED DE INICIO] comienza a parpadear en amarillo indicando)
  • Presione [X] para apagar la calibración automática y continuar con la calibración manual.
  • - Gire RS y LS lenta y completamente tocando las esquinas del anillo 4 veces.
  • - Presione y suelte completamente R2 y L2 3 veces.
  • - Una vez que se hayan recopilado suficientes datos para la calibración de los sensores Hall, el controlador vibra una vez. El usuario puede proceder al siguiente paso.
  • - Coloque el controlador sobre una superficie plana y estable, luego presione [OPTION] para iniciar la calibración del giroscopio.
  • - Una vez finalizada la calibración del giroscopio, el controlador sale de la configuración y vuelve al modo de espera.

Video Tutorial: 

 



The QRD SPARK N5 uses Hall Effect joysticks to provide smooth analog control while reducing wear-related stick drift.

If you notice that your character, camera, or cursor moves slightly even when the joystick is released, this does not necessarily mean that the joystick hardware is defective.

In many cases, drift-like behavior can be caused by:

  • Joysick caps loosing
  • Incorrect automatic calibration
  • Moving the joysticks or analog triggers while the controller is starting
  • An incorrect calibration reference
  • Improper joystick sensitivity or deadzone settings
  • Game-specific deadzone settings

Please follow the troubleshooting steps below in order.


Manually Adjust the Joystick Position

Due to long periods of shipping, the joystick cap may become loose from the Hall sensor inside the controller, causing the joystick to drift. We recommend manually adjusting the joystick cap to ensure it is correctly aligned at the center.

 How to Perform: 
Cómo solucionar el problema de la deriva del joystick QRD Spark N5
  1. Disconnect the Controller: First, disconnect the controller from the console or any device.
  2. Remove the Joystick Cap: Gently pull off the joystick cap from the joystick.
  3. Adjust the Joystick Cap: After removing the cap, slowly rotate the base of the joystick cap either clockwise or counterclockwise for 3-4 turns. Make sure there are no unusual looseness or resistance during this process.
  4. Re-align to the Center: Once the rotation is smooth, ensure the joystick cap is aligned to the center, then gently press it down to secure it in place.

 Restore Automatic Calibration Mode  
STEP 1: Enter Calibration Settings
  • - while the controller is turned off, hold down the [TURBO+OPTION+HOME] for 3 seconds to enter calibration settings menu. ( [HOME LED] starts flashing yellow color indicating)

STEP 2: Enable Automatic Calibration

While the HOME LED is flashing:

Press:

Square (□)

Pressing □:

  • Turns Automatic Calibration ON
  • Exits Calibration Settings
  • Returns the controller to standby mode

Automatic Calibration has now been successfully restored.

 Restart the Controller Complete the Auto-Cali bration

 Test the Controller Again 

https://hardwaretester.com/gamepad

After completing the automatic calibration process:

  1. Release both joysticks.
  2. Make sure LS and RS return naturally to the center position.
  3. Launch the game where the drift occurred.
  4. Leave both sticks untouched.
  5. Check whether the character, camera, cursor, or vehicle still moves by itself.

If possible, also test the controller:

  • In another game
  • On another PC or console
  • In a gamepad input testing tool

This helps determine whether the issue is coming from the controller itself or from a game-specific deadzone configuration.


If Automatic Calibration Does Not Solve the Problem, Use Manual Calibration

Manual Calibration should normally be used after:

  1. Firmware has been updated
  2. Automatic Calibration has been restored
  3. Startup calibration has been completed correctly
  4. The controller has been hardware-reset and retested

If the joystick still behaves abnormally, Manual Calibration can be used to redefine the analog movement range directly.

QRD SPARK N5

Manual Calibration Tutorials Video

Official tutorial

03:45

Follow each step carefully. Do not disconnect the USB cable during the update.

View on YouTube
STEP 1: Enter Manual Calibration Mode
  • - while the controller is turned off, hold down the [TURBO+OPTION+HOME] for 3 seconds to enter calibration settings menu. ( [HOME LED] starts flashing yellow color indicating)
STEP 2: Disable Automatic Calibration

Press:

Cross (×)

This:

Turns Automatic Calibration OFF

Enters Manual Calibration Mode

Once Automatic Calibration has been disabled, complete the entire manual calibration procedure before returning to normal use.

STEP 3: Manually Calibrate the Hall Effect Joysticks
  • Slowly rotate the LS around its complete physical range.

Complete at least: 【4 full rotations】

Make sure it touches the full outer movement range in every direction.

Do not make fast or incomplete circles.

The calibration system needs complete minimum and maximum analog-range data.

STEP 4: Manually Calibrate the Analog Triggers
  • Slowly press:

    L2&R2 → fully down → release

Repeat at least: 【3 times】

After enough Hall sensor calibration data has been collected, the controller will briefly vibrate.

This vibration confirms that joystick and trigger calibration has been completed successfully.

STEP 5: Calibrate the 6-Axis Gyroscope

Place the controller on a:

Flat surface

Stable surface

Level surface

Motionless surface

Do not hold or move the controller.

  • 【Press: OPTION】

The controller will begin calibrating the built-in gyroscope.

Keep the controller completely still.

When calibration is successfully completed:

The controller will vibrate

Calibration Mode will close automatically

The controller will return to standby

Manual Calibration will remain enabled

You can now reconnect the controller and test the joysticks again.

Finish the Test again


Check the Game's Deadzone Settings

×

DISFRUTA DE UN 5 % DE DESCUENTO EN TU PEDIDO*

Sign up for our newsletter to receive exclusive drops, special offers, and your instant discount code.

No thanks, I prefer paying full price