QRD SPARK N5 PS5/PS4/PS3 Games Trigger Tips – Improve Rapid Fire Input – qrdgame

When playing FPS games on PS5, PS4 or PS3, some players may notice that rapidly pressing the L2/R2 triggers does not always feel as responsive as repeatedly pressing a normal button.

This does not necessarily mean that the trigger is defective.

The QRD SPARK N5 uses Hall Effect analog triggers. Unlike a standard digital button, L2/R2 continuously reports its travel position from released to fully pressed.

In many FPS games, a Fire command is recognized only when the trigger input crosses the activation threshold defined by the game.

For another shot to be recognized, the trigger normally needs to:

Press past the activation point → Release far enough → Press past the activation point again

When R2 is pressed repeatedly very quickly, the trigger may not always return far enough into the game's release range before the next press. In some games, the next input may therefore not be recognized as a new Fire command.

This can feel like trigger delay, even when the controller itself is working normally.


Why Is This More Noticeable on PlayStation?

On PC, Steam Input can provide additional trigger settings that may allow players to adjust how analog trigger input is interpreted.

On PS5, PS4 and PS3, there is no equivalent universal system-level setting for adjusting the QRD SPARK N5 trigger activation threshold.

The actual response therefore depends mainly on:

SPARK N5 Analog Trigger → Game Trigger Threshold → Fire Command

Some games provide their own trigger/deadzone settings, while others do not.

If the problem only occurs during rapid repeated fire in a specific game, it should not immediately be treated as a trigger hardware failure.


Gameplay Tip: Map Fire to N1/N2

For FPS games where R2 is used simply as a Fire command, players can try assigning R2 to one of the programmable N1/N2 back paddles.

For example:

R2 / Fire → N1

The back paddle provides a short button-style operation and can be easier to press repeatedly during high-frequency shooting.

How to Set R2 to N1

  1. Hold SET + N1 until the indicator starts flashing.
  2. Press R2 once.
  3. Press N1 again to save.

Now:

Press N1 → Execute the recorded R2 / Fire command

You can use the original R2 normally at any time, while N1 provides an additional control option for rapid-fire situations.


When Is This Tip Useful?

This setup can be useful in FPS/TPS games where R2 functions as a simple Fire command, especially when using:

  • Semi-automatic weapons
  • Pistols
  • Single-shot rifles
  • Other weapons requiring frequent repeated trigger presses

Popular examples include Call of Duty / Warzone, Apex Legends, Fortnite and Battlefield, depending on the player's current in-game button layout.

The game itself still determines the weapon's maximum fire rate.


Important: This Is a Gameplay Tip, Not a Trigger Repair

Mapping R2 to N1 does not:

  • Change the Hall Effect trigger parameters
  • Change the game's Trigger Threshold
  • Increase controller polling rate
  • Reduce Bluetooth or USB latency
  • Repair a physically defective trigger

It simply provides another way to execute the same Fire command.

This makes it useful both as a gameplay optimization and as a quick comparison test.

If R2 feels inconsistent during rapid fire, but N1 works normally:

The issue may be related to the analog trigger travel and the game's activation/release threshold.

If R2 and N1 show the same delayed response:

The cause is more likely related to the game, connection or system response rather than the physical trigger travel.


When Should You Troubleshoot the Trigger?

Further trigger troubleshooting is recommended if L2/R2 also behaves abnormally when pressed slowly, or if the problem occurs across multiple games.

Examples include:

  • Trigger does not register
  • Trigger cannot reach full input
  • Trigger activates without being pressed
  • Input remains abnormal after full press and release
  • The same issue occurs in multiple games

In these situations, perform the official QRD SPARK N5 trigger calibration and troubleshooting procedure.


STEP 1: Enter Manual Calibration Mode
  • - while the controller is turned off, hold down the [TURBO+OPTION+HOME] for 3 seconds to enter calibration settings menu. ( [HOME LED] starts flashing yellow color indicating)
STEP 2: Disable Automatic Calibration

Press:

Cross (×)

This:

Turns Automatic Calibration OFF

Enters Manual Calibration Mode

Once Automatic Calibration has been disabled, complete the entire manual calibration procedure before returning to normal use.

STEP 3: Manually Calibrate the Hall Effect Joysticks
  • Slowly rotate the LS around its complete physical range.

Complete at least: 【4 full rotations】

Make sure it touches the full outer movement range in every direction.

Do not make fast or incomplete circles.

The calibration system needs complete minimum and maximum analog-range data.

STEP 4: Manually Calibrate the Analog Triggers
  • Slowly press:

    L2&R2 → fully down → release

Repeat at least: 【3 times】

After enough Hall sensor calibration data has been collected, the controller will briefly vibrate.

This vibration confirms that joystick and trigger calibration has been completed successfully.

STEP 5: Calibrate the 6-Axis Gyroscope

Place the controller on a:

Flat surface

Stable surface

Level surface

Motionless surface

Do not hold or move the controller.

  • 【Press: OPTION】

The controller will begin calibrating the built-in gyroscope.

Keep the controller completely still.

When calibration is successfully completed:

The controller will vibrate

Calibration Mode will close automatically

The controller will return to standby

Manual Calibration will remain enabled

You can now reconnect the controller and test the joysticks again.

×

DISFRUTA DE UN 5 % DE DESCUENTO EN TU PEDIDO*

Sign up for our newsletter to receive exclusive drops, special offers, and your instant discount code.

No thanks, I prefer paying full price